This SaniBEST Upflush Kit Includes. The SaniBEST macerating bathroom pump. White toilet bowl (size: standard). The SaniBEST is a system that is used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. The SaniBEST pump is designed to connect with.
The SaniBEST is simplicity itself to install; there are just four connections. The macerating/pump is connected to the spigot of a horizontal outlet toilet. The toilet tank is connected to the water supply. The macerating/pump is connected to the small diameter discharge pipe work.The macerating/pump is connected to the electrical supply. Then optionally connect the discharge pipes from the sink, shower and/or bath.
The inside of the SaniBEST is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel cutting blade and the pump. When the flush is activated, the water flowing into the SaniBEST activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the blades.
The moving parts therefore are kept to an absolute minimum. Water and organic waste matter, enter the chamber and are reduced to slurry as the blades rotate at 3600 RPM. The reduced solids are picked up at the bottom and the impeller mounted beneath the motor ejects the waste.
The unit pumps the effluent upward to 18 feet and/or 150 feet horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates. A normal operating cycle for the SaniBEST takes about 7-9 seconds depending upon the discharge pipe run configuration. In addition, the SaniBEST will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bath/shower, a urinal and even a washing machine (indirect connection).
When adding a bathtub/shower, a base will have to be constructed. This base should be made out of a 2 x 6 (minimum) or 2x 8 (recommended) on edge, to allow for the installation of a P-trap and the required 1/4 per foot gravity flow towards the pump unit.
The wastewater from other sanitary fixtures is discharged into the SaniBEST via two 1½-inch inlets on either side of the housing. The discharge elbow on top of the SaniBEST can be rotated 360 degrees depending on the discharge installation.
A non-return valve (included in assembly) prevents back flow into the unit. This unit has been designed with a vent connection on the lid.
All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems. The SaniBEST unit must be connected to our rear discharge toilet.
It is highly recommended for the grinder to be connected to a Ground Fault Interrupter (GFI) circuit. The Sanibest has been certified to American and Canadian Standards. Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9. The water closet the SaniBEST is connected to, uses much less water than a regular toilet, it uses 6 liters (1.6 US Gal) of water per flush. UPC#s 013, 003 and 005.
H10" x W21" x D9. H26cm x W53cm x D23cm. No carbon brushes or gears. Tested over 30,000 cycles. Horizontally to 150 ft (50m).
Gravity Fall on Horizontal installations: 1/4 per ft. Pumps vertically to 18 ft (5.5m). Subject to installation pipe run. Top rated, authorized SaniFlo dealer.
The item "Saniflo SaniBEST Macerating Upflush Toilet Kit Pump + Standard Bowl" is in sale since Thursday, September 6, 2012. This item is in the category "Home & Garden\Bath\Toilets & Bidets\Toilet Parts & Attachments". The seller is "upflushtoilet" and is located in Salamanca, New York. This item can be shipped to United States.